The Notebooks of Leonardo Da Vinci. Complete

I must in these remarks confine myself strictly to the task in hand and give no more of the history of the Sforza monument than is needed to explain the texts and drawings I have been able to reproduce. In the first place, with regard to the drawings, I may observe that they are all, with the following two exceptions, in the Queen's Library at Windsor Castle; the red chalk drawing on Pl. LXXVI No. 1 is in the MS. C. A. (see No. 7l2) and the fragmentary pen and ink drawing on page 4 is in the Ambrosian Library. The drawings from Windsor on Pl. LXVI have undergone a trifling reduction from the size of the originals.

There can no longer be the slightest doubt that the well-known engraving of several horsemen (Passavant, Le Peintre-Graveur, Vol. V, p. 181, No. 3) is only a copy after original drawings by Leonardo, executed by some unknown engraver; we have only to compare the engraving with the facsimiles of drawings on Pl. LXV, No. 2, Pl. LXVII, LXVIII and LXIX which, it is quite evident, have served as models for the engraver.

On Pl. LXV No. 1, in the larger sketch to the right hand, only the base is distinctly visible, the figure of the horseman is effaced. Leonardo evidently found it unsatisfactory and therefore rubbed it out.

The base of the monument—the pedestal for the equestrian statue—is repeatedly sketched on a magnificent plan. In the sketch just mentioned it has the character of a shrine or aedicula to contain a sarcophagus. Captives in chains are here represented on the entablature with their backs turned to that portion of the monument which more

strictly constitutes the pedestal of the horse. The lower portion of the aedicula is surrounded by columns. In the pen and ink drawing Pl. LXVI—the lower drawing on the right hand side—the sarcophagus is shown between the columns, and above the entablature is a plinth on which the horse stands. But this arrangement perhaps seemed to Leonardo to lack solidity, and in the little sketch on the left hand, below, the sarcophagus is shown as lying under an arched canopy. In this the trophies and the captive warriors are detached from the angles. In the first of these two sketches the place for the trophies is merely indicated by a few strokes; in the third sketch on the left the base is altogether broader, buttresses and pinnacles having been added so as to form three niches. The black chalk drawing on Pl. LXVIII shows a base in which the angles are formed by niches with pilasters. In the little sketch to the extreme left on Pl. LXV, No. 1, the equestrian statue serves to crown a circular temple somewhat resembling Bramante's tempietto of San Pietro in Montario at Rome, while the sketch above to the right displays an arrangement faintly reminding us of the tomb of the Scaligers in Verona. The base is thus constructed of two platforms or slabs, the upper one considerably smaller than the lower one which is supported on flying buttresses with pinnacles.

On looking over the numerous studies in which the horse is not galloping but merely walking forward, we find only one drawing for the pedestal, and this, to accord with the altered character of the statue, is quieter and simpler in style (Pl. LXXIV). It rises almost vertically from the ground and is exactly as long as the pacing horse. The whole base is here arranged either as an independent baldaquin or else as a projecting canopy over a recess in which the figure of the deceased Duke is seen lying on his sarcophagus; in the latter case it was probably intended as a tomb inside a church. Here, too, it was intended to fill the angles with trophies or captive warriors. Probably only No. 724 in the text refers to the work for the base of the monument.

If we compare the last mentioned sketch with the description of a plan for an equestrian monument to Gian Giacomo Trivulzio (No. 725) it seems by no means impossible that this drawing is a preparatory study for the very monument concerning which the manuscript gives us detailed information. We have no historical record regarding this sketch nor do the archives in the Trivulzio Palace give us any information. The simple monument to the great general in San Nazaro Maggiore in Milan consists merely of a sarcophagus placed in recess high on the wall of an octagonal chapel. The figure of the warrior is lying on the sarcophagus, on which his name is inscribed; a piece of sculpture which is certainly not Leonardo's work. Gian Giacomo Trivulzio died at Chartres in 1518, only five months before Leonardo, and it seems to me highly improbable that this should have been the date of this sketch; under these circumstances it would have been done under the auspices of Francis I, but the Italian general was certainly not in favour with the French monarch at the time. Gian Giacomo Trivulzio was a sworn foe to Ludovico il Moro, whom he strove for years to overthrow. On the 6th September 1499 he marched victorious into Milan at the head of a French army. In a short time, however, he was forced to quit Milan again when Ludovico il Moro bore down upon the city with a force of Swiss troops. On the 15th of April following, after defeating Lodovico at Novara, Trivulzio once more entered Milan as a Conqueror, but his hopes of becoming Governatore of the place were soon wrecked by intrigue. This victory and triumph, historians tell us, were signalised by acts of vengeance against the dethroned Sforza, and it might have been particularly flattering to him that the casting and construction of the Sforza monument were suspended for the time.

It must have been at this moment—as it seems to me—that he commissioned the artist to prepare designs for his own monument, which he probably intended should find a place in the Cathedral or in some other church. He, the husband of Margherita di Nicolino Colleoni, would have thought that he had a claim to the same distinction and public homage as his less illustrious connection had received at the hands of the Venetian republic. It was at this very time that Trivulzio had a medal struck with a bust portrait of himself and the following remarkable inscription on the reverse:_ DEO FAVENTE—1499—DICTVS—10—IA—EXPVLIT—LVDOVICV—SF— (Sfortiam) DVC— (ducem) MLI (Mediolani)—NOIE (nomine)—REGIS—FRANCORVM—EODEM—ANN —(anno) RED'T (redit)—LVS (Ludovicus)—SVPERATVS ET CAPTVS—EST—AB—EO. _In the Library of the Palazzo Trivulzio there is a MS. of Callimachus Siculus written at the end of the XVth or beginning of the XVIth century. At the beginning of this MS. there is an exquisite illuminated miniature of an equestrian statue with the name of the general on the base; it is however very doubtful whether this has any connection with Leonardo's design.

Nos. 731-740, which treat of casting bronze, have probably a very indirect bearing on the arrangements made for casting the equestrian statue of Francesco Sforza. Some portions evidently relate to the casting of cannon. Still, in our researches about Leonardo's work on the monument, we may refer to them as giving us some clue to the process of bronze casting at that period.

Some practical hints (706-709).

706

OF A STATUE.

If you wish to make a figure in marble, first make one of clay, and when you have finished it, let it dry and place it in a case which should be large enough, after the figure is taken out of it, to receive also the marble, from which you intend to reveal the figure in imitation of the one in clay. After you have put the clay figure into this said case, have little rods which will exactly slip in to the holes in it, and thrust them so far in at each hole that each white rod may touch the figure in different parts of it. And colour the portion of the rod that remains outside black, and mark each rod and each hole with a countersign so that each may fit into its place. Then take the clay figure out of this case and put in your piece of marble, taking off so much of the marble that all your rods may be hidden in the holes as far as their marks; and to be the better able to do this, make the case so that it can be lifted up; but the bottom of it will always remain under the marble and in this way it can be lifted with tools with great ease.

707

Some have erred in teaching sculptors to measure the limbs of their figures with threads as if they thought that these limbs were equally round in every part where these threads were wound about them.

708

MEASUREMENT AND DIVISION OF A STATUE.

Divide the head into 12 degrees, and each degree divide into 12 points, and each point into 12 minutes, and the minutes into minims and the minims into semi minims.

Degree—point—minute—minim.

709

Sculptured figures which appear in motion, will, in their standing position, actually look as if they were falling forward.

[Footnote: figure di rilievo. Leonardo applies this term exclusively to wholly detached figures, especially to those standing free. This note apparently refers to some particular case, though we have no knowledge of what that may have been. If we suppose it to refer to the first model of the equestrian statue of Francesco Sforza (see the introduction to the notes on Sculpture) this observation may be regarded as one of his arguments for abandoning the first scheme of the Sforza Monument, in which the horse was to be galloping (see page 2). It is also in favour of this theory that the note is written in a manuscript volume already completed in 1492. Leonardo's opinions as to the shortcomings of plastic works when compared with paintings are given under No. 655 and 656.]

Notes on the casting of the Sforza monument (710-715).

710

Three braces which bind the mould.

[If you want to make simple casts quickly, make them in a box of river sand wetted with vinegar.]

[When you shall have made the mould upon the horse you must make the thickness of the metal in clay.]

Observe in alloying how many hours are wanted for each hundredweight. [In casting each one keep the furnace and its fire well stopped up.] [Let the inside of all the moulds be wetted with linseed oil or oil of turpentine, and then take a handful of powdered borax and Greek pitch with aqua vitae, and pitch the mould over outside so that being under ground the damp may not [damage it?]

[To manage the large mould make a model of the small mould, make a small room in proportion.]

[Make the vents in the mould while it is on the horse.]

Hold the hoofs in the tongs, and cast them with fish glue. Weigh the parts of the mould and the quantity of metal it will take to fill them, and give so much to the furnace that it may afford to each part its amount of metal; and this you may know by weighing the clay of each part of the mould to which the quantity in the furnace must correspond. And this is done in order that the furnace for the legs when filled may not have to furnish metal from the legs to help out the head, which would be impossible. [Cast at the same casting as the horse the little door]

[Footnote: The importance of the notes included under this number is not diminished by the fact that they have been lightly crossed out with red chalk. Possibly they were the first scheme for some fuller observations which no longer exist; or perhaps they were crossed out when Leonardo found himself obliged to give up the idea of casting the equestrian statue. In the original the first two sketches are above l. 1, and the third below l. 9.]

711

THE MOULD FOR THE HORSE.

Make the horse on legs of iron, strong and well set on a good foundation; then grease it and cover it with a coating, leaving each coat to dry thoroughly layer by layer; and this will thicken it by the breadth of three fingers. Now fix and bind it with iron as may be necessary. Moreover take off the mould and then make the thickness. Then fill the mould by degrees and make it good throughout; encircle and bind it with its irons and bake it inside where it has to touch the bronze.

OF MAKING THE MOULD IN PIECES.

Draw upon the horse, when finished, all the pieces of the mould with which you wish to cover the horse, and in laying on the clay cut it in every piece, so that when the mould is finished you can take it off, and then recompose it in its former position with its joins, by the countersigns.

The square blocks a b will be between the cover and the core, that is in the hollow where the melted bronze is to be; and these square blocks of bronze will support the intervals between the mould and the cover at an equal distance, and for this reason these squares are of great importance.

The clay should be mixed with sand.

Take wax, to return [what is not used] and to pay for what is used.

Dry it in layers.

Make the outside mould of plaster, to save time in drying and the expense in wood; and with this plaster enclose the irons [props] both outside and inside to a thickness of two fingers; make terra cotta. And this mould can be made in one day; half a boat load of plaster will serve you.

Good.

Dam it up again with glue and clay, or white of egg, and bricks and rubbish.

[Footnote: See Pl. LXXV. The figure "40," close to the sketch in the middle of the page between lines 16 and 17 has been added by a collector's hand.

In the original, below line 21, a square piece of the page has been cut out about 9 centimetres by 7 and a blank piece has been gummed into the place.

Lines 22-24 are written on the margin. l. 27 and 28 are close to the second marginal sketch. l. 42 is a note written above the third marginal sketch and on the back of this sheet is the text given as No. 642. Compare also No. 802.]

712

All the heads of the large nails.

[Footnote: See Pl. LXXVI, No. i. This drawing has already been published in the "Saggio delle Opere di L. da Vinci." Milano 1872, Pl. XXIV, No. i. But, for various reasons I cannot regard the editor's suggestions as satisfactory. He says: "Veggonsi le armature di legname colle quali forse venne sostenuto il modello, quando per le nozze di Bianca Maria Sforza con Massimiliano imperatore, esso fu collocato sotto un arco trionfale davanti al Castello."

713

These bindings go inside.

714

Salt may be made from human excrements, burnt and calcined, made into lees and dried slowly at a fire, and all the excrements produce salt in a similar way and these salts when distilled, are very strong.

[Footnote: VASARI repeatedly states, in the fourth chapter of his Introduzione della Scultura, that in preparing to cast bronze statues horse-dung was frequently used by sculptors. If, notwithstanding this, it remains doubtful whether I am justified in having introduced here this text of but little interest, no such doubt can be attached to the sketch which accompanies it.]

715

METHOD OF FOUNDING AGAIN.

This may be done when the furnace is made [Footnote: this note is written below the sketches.] strong and bruised.

Models for the horse of the Sforza monument (716-718).

716

Messer Galeazzo's big genet

717

Messer Galeazzo's Sicilian horse.

[Footnote: These notes are by the side of a drawing of a horse with figured measurements.]

718

Measurement of the Sicilian horse the leg from behind, seen in front, lifted and extended.

[Footnote: There is no sketch belonging to this passage. Galeazze here probably means Galeazze di San Severino, the famous captain who married Bianca the daughter of Ludovico il Moro.]

Occasional references to the Sforza monument (719-724).

719

Again, the bronze horse may be taken in hand, which is to be to the immortal glory and eternal honour of the happy memory of the prince your father, and of the illustrious house of Sforza.

[Footnote: The letter from which this passage is here extracted will be found complete in section XXI. (see the explanation of it, on page 2).]

720

On the 23rd of April 1490 I began this book, and recommenced the horse.

721

There is to be seen, in the mountains of Parma and Piacenza, a multitude of shells and corals full of holes, still sticking to the rocks, and when I was at work on the great horse for Milan, a large sackful of them, which were found thereabout, was brought to me into my workshop, by certain peasants.

722

Believe me, Leonardo the Florentine, who has to do the equestrian bronze statue of the Duke Francesco that he does not need to care about it, because he has work for all his life time, and, being so great a work, I doubt whether he can ever finish it. [Footnote: This passage is quoted from a letter to a committee at Piacenza for whom Leonardo seems to have undertaken to execute some work. The letter is given entire in section XXL; in it Leonardo remonstrates as to some unreasonable demands.]

723

Of the horse I will say nothing because I know the times. [Footnote: This passage occurs in a rough copy of a letter to Ludovico il Moro, without date (see below among the letters).]

724

During ten years the works on the marbles have been going on I will not wait for my payment beyond the time, when my works are finished. [Footnote: This possibly refers to the works for the pedestal of the equestrian statue concerning which we have no farther information in the MSS. See p. 6.]

The project of the Trivulzio monument.

725

THE MONUMENT TO MESSER GIOVANNI JACOMO DA TREVULZO.

[2] Cost of the making and materials for the horse [5].

[Footnote: In the original, lines 2-5, 12-14, 33-35, are written on the margin. This passage has been recently published by G. Govi in Vol. V, Ser. 3a, of Transunti, Reale Accademia dei Linea, sed. del 5 Giugno, 1881, with the following introductory note: "Desidero intanto che siano stampati questi pochi frammenti perche so che sono stati trascritti ultimamente, e verranno messi in luce tra poco fuori d'Italia. Li ripubblichi pure chi vuole, ma si sappia almeno che anche tra noi si conoscevano, e s'eran raccolti da anni per comporne, quando che fosse, una edizione ordinata degli scritti di Leonardo."

The learned editor has left out line 22 and has written 3 pie for 8 piedi in line 25. There are other deviations of less importance from the original.]

A courser, as large as life, with the rider requires for the cost of the metal, duc. 500.

And for cost of the iron work which is inside the model, and charcoal, and wood, and the pit to cast it in, and for binding the mould, and including the furnace where it is to be cast … duc. 200.

To make the model in clay and then in wax……… duc. 432.

To the labourers for polishing it when it is cast. ……. duc. 450.

in all. . duc. 1582.

[12] Cost of the marble of the monument [14].

Cost of the marble according to the drawing. The piece of marble under the horse which is 4 braccia long, 2 braccia and 2 inches wide and 9 inches thick 58 hundredweight, at 4 Lire and 10 Soldi per hundredweight.. duc. 58.

And for 13 braccia and 6 inches of cornice, 7 in. wide and 4 in. thick, 24 hundredweight……. duc. 24.

And for the frieze and architrave, which is 4 br. and 6 in. long, 2 br. wide and 6 in. thick, 29 hundredweight., duc. 20.

And for the capitals made of metal, which are 8, 5 inches in. square and 2 in. thick, at the price of 15 ducats each, will come to…… duc. 122.

And for 8 columns of 2 br. 7 in., 4 1/2 in. thick, 20 hundredweight duc. 20.

And for 8 bases which are 5 1/2 in. square and 2 in. high 5 hund'.. duc. 5.

And for the slab of the tombstone 4 br. io in. long, 2 br. 4 1/2 in. wide 36 hundredweight……. duc. 36.

And for 8 pedestal feet each 8 br. long and 6 1/2 in. wide and 6 1/2 in. thick, 20 hundredweight come to… duc. 20.

And for the cornice below which is 4 br. and 10 in. long, and 2 br. and 5 in. wide, and 4 in. thick, 32 hund'.. duc. 32.

And for the stone of which the figure of the deceased is to be made which is 3 br. and 8 in. long, and 1 br. and 6 in. wide, and 9 in. thick, 30 hund'.. duc. 30.

And for the stone on which the figure lies which is 3 br. and 4 in. long and 1 br. and 2 in., wide and 4 1/2 in. thick duc. 16.

And for the squares of marble placed between the pedestals which are 8 and are 9 br. long and 9 in. wide, and 3 in. thick, 8 hundredweight . . . duc. 8. in all. . duc. 389.

[33]Cost of the work in marble[35].

Round the base on which the horse stands there are 8 figures at 25 ducats each ………… duc. 200.

And on the same base there are 8 festoons with some other ornaments, and of these there are 4 at the price of 15 ducats each, and 4 at the price of 8 ducats each ……. duc. 92.

And for squaring the stones duc. 6.

Again, for the large cornice which goes below the base on which the horse stands, which is 13 br. and 6 in., at 2 due. per br. …… duc. 27.

And for 12 br. of frieze at 5 due. per br. ……….. duc. 60.

And for 12 br. of architrave at 1 1/2 duc. per br. ……. duc. 18.

And for 3 rosettes which will be the soffit of the monument, at 20 ducats each ………. duc. 60.

And for 8 fluted columns at 8 ducats each ……… duc. 64.

And for 8 bases at 1 ducat each, duc. 8.

And for 8 pedestals, of which 4 are at 10 duc. each, which go above the angles; and 4 at 6 duc. each .. duc. 64.

And for squaring and carving the moulding of the pedestals at 2 duc. each, and there are 8 …. duc. 16.

And for 6 square blocks with figures and trophies, at 25 duc. each .. duc. 150.

And for carving the moulding of the stone under the figure of the deceased ………. duc. 40.

For the statue of the deceased, to do it well ………. duc. 100.

For 6 harpies with candelabra, at 25 ducats each ……… duc. 150.

For squaring the stone on which the statue lies, and carving the moulding ………… duc. 20.

in all .. duc. 1075.

The sum total of every thing added together amount to …… duc. 3046.

726

MINT AT ROME.

It can also be made without a spring. But the screw above must always be joined to the part of the movable sheath: [Margin note: The mint of Rome.] [Footnote: See Pl. LXXVI. This passage is taken from a note book which can be proved to have been used in Rome.]

All coins which do not have the rim complete, are not to be accepted as good; and to secure the perfection of their rim it is requisite that, in the first place, all the coins should be a perfect circle; and to do this a coin must before all be made perfect in weight, and size, and thickness. Therefore have several plates of metal made of the same size and thickness, all drawn through the same gauge so as to come out in strips. And out of [24] these strips you will stamp the coins, quite round, as sieves are made for sorting chestnuts [27]; and these coins can then be stamped in the way indicated above; &c.

[31] The hollow of the die must be uniformly wider than the lower, but imperceptibly [35].

This cuts the coins perfectly round and of the exact thickness, and weight; and saves the man who cuts and weighs, and the man who makes the coins round. Hence it passes only through the hands of the gauger and of the stamper, and the coins are very superior. [Footnote: See Pl. LXXVI No. 2. The text of lines 31-35 stands parallel 1. 24-27.

Farther evidence of Leonardo's occupations and engagements at Rome under Pope Leo X. may be gathered from some rough copies of letters which will be found in this volume. Hitherto nothing has been known of his work in Rome beyond some doubtful, and perhaps mythical, statements in Vasari.]

727

POWDER FOR MEDALS.

The incombustible growth of soot on wicks reduced to powder, burnt tin and all the metals, alum, isinglass, smoke from a brass forge, each ingredient to be moistened, with aqua vitae or malmsey or strong malt vinegar, white wine or distilled extract of turpentine, or oil; but there should be little moisture, and cast in moulds. [Margin note: On the coining of medals (727. 728).] [Footnote: The meaning of scagliuolo in this passage is doubtful.]

728